az10ep16vs az100ep16vs ecl/pecl differential receiv er with variable output swing 1630 s. stapley dr., suite 125 ? mesa, arizona 85204 ? usa ? (480) 962-5881 ? fax (480) 890-2541 www.azmicrotek.com arizona microtek, inc. features ? silicon-germanium for high speed operation ? 150ps typical propagation delay ? az100ep16vs functionally equivalent to on semiconductor mc100ep16vs at 3.3v ? available in a 3x3mm mlp package description the az10/100ep16vs is a silicon?germanium (sige) differe ntial receiver with variab le output swing. the ep16vs has functionality and output transition times similar to the ep16, with an input that controls the amplitude of the q/q outputs. the operational range of the ep16vs control input, v ctrl , is from v ref (full swing) to v cc (min. swing). maximum swing is achieved by leaving the v ctrl pin open or tied to v ee . simple control of the output swing can be obtained by a variable resistor between the v ref and v cc pins, with the wiper driving v ctrl . typical application circuits and results are described in this data sheet. the ep16vs provides a v ref output for a dc bias for ac coupling to the device. the v ref pin should be used only as a bias for the ep16vs as its current sink/source capability is limited. whenever used, the v ref pin should be bypassed to ground via a 0.01 f capacitor. under open input conditions for d/d , the q/q outputs are not guaranteed. note: specifications in ecl/pecl tables are valid when thermal equilibrium is established. package availability package part no. marking mlp 8 az10ep16vsl azm16e mlp 8 t&r az10ep16vslr1 azm16e mlp 8 t&r az10ep16vslr2 azm16e mlp 8 az100ep16vsl azm16f mlp 8 t&r az100ep16vslr1 azm16f mlp 8 t&r AZ100EP16VSLR2 azm16f soic 8 az10ep16vsd azm10ep16vs soic 8 t&r az10ep16vsdr1 azm10ep16vs soic 8 t&r az10ep16vsdr2 azm10ep16vs soic 8 az100ep16vsd azm100ep16vs soic 8 t&r az100ep16vsdr1 azm100ep16vs soic 8 t&r az100ep16vsdr2 azm100ep16vs tssop 8 az10ep16vst aztp16vs tssop 8 t&r az10ep16vstr1 aztp16vs tssop 8 t&r az10ep16vstr2 aztp16vs tssop 8 az100ep16vst azhp16vs tssop 8 t&r az100ep16vstr1 azhp16vs tssop 8 t&r az100ep16vstr2 azhp16vs
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 2 absolute maximum ratings are those values beyond which device life may be impaired. symbol characteristic rating unit v cc pecl power supply (v ee = 0v) 0 to +4.5 vdc v i pecl input voltage (v ee = 0v) 0 to +4.5 vdc v ee ecl power supply (v cc = 0v) -4.5 to 0 vdc v i ecl input voltage (v cc = 0v) -4.5 to 0 vdc i out output current --- continuous --- surge 50 100 ma t a operating temperature range -40 to +85 c t stg storage temperature range -65 to +150 c 10k ecl dc characteristics (v ee = -3.0v to -3.6v, v cc = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1085 -835 -1020 -895 -770 -960 -710 mv v ol output low voltage 1 v ctrl = v ref -2115 -1865 -2050 -1925 -1800 -1990 -1740 mv v ol output low voltage 1 v ctrl = v cc -1330 -1080 -1265 -1140 -1015 -1205 -915 mv v ref reference voltage -1700 -1600 -1500 -1670 -1570 -1470 -1650 -1550 -1450 -1600 -1500 -1400 mv i ih input high current d,d v ctrl 80 400 80 400 80 400 80 400 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 21 27 36 22 28 37 22 29 38 24 30 40 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. logic diagram and pinout assignment pin description pin function d, d data inputs v ctrl output swing control q, q data outputs v ref reference voltage output v cc positive supply v ee negative supply 8 4 5 6 3 2 1 7 v cc d v ee q q v ref d v ctrl 8 soic & 8 tssop mlp 8 ( top view ) 8 5 6 7 4 3 2 1 v cc d v ee q q v ref d v ctrl
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 3 10k lvpecl dc characteristics (v ee = gnd, v cc = +3.3v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 2215 2465 2280 2405 2530 2340 2590 mv v ol output low voltage 2 v ctrl = v ref 1185 1435 1250 1375 1500 1310 1560 mv v ol output low voltage 2 v ctrl = v cc 1970 2220 2035 2160 2285 2095 2385 mv v ref reference voltage 1600 1700 1800 1630 1730 1830 1650 1750 1850 1700 1800 1900 mv i ih input high current d,d v ctrl 80 400 80 400 80 400 80 400 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 21 27 36 22 28 37 22 29 38 24 30 40 ma 1. for supply voltages other that 3.3v, use the ecl table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 100k ecl dc characteristics (v ee = -3.0v to -3.6v, v cc = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1095 -890 -1035 -890 -1035 -965 -890 -1035 -890 mv v ol output low voltage 1 v ctrl = v ref -1925 -1835 -1965 -1775 -1965 -1870 -1775 -1965 -1775 mv v ol output low voltage 1 v ctrl = v cc -1180 -1045 -1160 -970 -1160 -1065 -970 -1160 -970 mv v ref reference voltage -1650 -1450 -1650 -1450 -1650 -1550 -1450 -1650 -1450 mv i ih input high current d,d v ctrl 80 400 80 400 80 400 80 400 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 20 26 35 21 27 36 22 28 38 25 31 41 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. 100k lvpecl dc characteristics (v ee = gnd, v cc = +3.3v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 3905 4110 3965 4110 3965 4035 4110 3965 4110 mv v ol output low voltage 2 v ctrl = v ref 3075 3165 3035 3225 3035 3130 3225 3035 3225 mv v ol output low voltage 2 v ctrl = v cc 3820 3955 3840 4030 3840 3935 4030 3840 4030 mv v ref reference voltage 1650 1850 1650 1850 1650 1750 1850 1650 1850 mv i ih input high current d,d v ctrl 80 400 80 400 80 400 80 400 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 20 26 35 21 27 36 22 28 38 25 31 41 ma 1. for supply voltages other that 3.3v, use the ecl table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v.
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 4 ac characteristics (v ee = -3.0 to -3.6v, v cc = gnd, v ctrl =v ref or v ee = gnd, v cc = +3.0v to 3.6v, v ctrl = v ref ) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit f max maximum toggle frequency 5 >4 >4 >4 >4 ghz t plh / t phl input to output delay (diff) (se) 100 150 155 240 100 150 155 240 100 150 155 240 120 170 175 280 ps t skew duty cycle skew 1 (diff) 4 20 4 15 4 15 4 15 ps v pp minimum input swing 2 150 150 150 150 mv v cmr common mode range 3 v ee + 2.0 v cc v ee + 2.0 v cc v ee + 2.0 v cc v ee + 2.0 v cc v a v small signal gain 4 28 db t r / t f output rise/fall times q (20% - 80%) 120 70 120 180 120 180 120 200 ps 1. duty cycle skew is the difference between a t plh and t phl propagation delay through a device. 2. v pp is the minimum peak-to-peak differential input swing for which ac parameters are guaranteed. 3. the v cmr range is referenced to the most positive side of the differential input signal. no rmal operation is obtained if the high leve l falls within the specified range and the peak -to-peak voltage lies between v pp (min) and 1v. 4. differential input, differential output. 240 ? to v ee on q/q outputs and v ctrl = open circuit. 5. see graph below. large signal performance* 0 100 200 300 400 500 600 700 800 900 1000 0 1000 2000 3000 4000 5000 6000 frequency (mhz) v outpp (mv) v ctrl =v cc v ctrl =v cc -2.0v v ctrl =v cc -1.5v v ctrl =v cc -1.0v v ctrl =v cc -0.5v *measured using a 750mv differential input source at 50% duty cycle.
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 5 typical az100ep16vs voltage output swing at +25c, v ee nom (see figure 1 and figure 2) 1.240 v (100k ecl) 0 25 50 75 100 0.0 0.4 0.8 1.2 1.6 v ctrl (v) v swing (% pk-pk differential) %out 100k ecl figure 2: alternative implementation 8 5 6 7 4 3 2 1 v cc d v ee q q v ref d v ctrl v ctrl 50 -2v 50 v swing (pk-pk) figure 1: voltage source implementation 8 5 6 7 4 3 2 1 v cc d v ee q q v ref d v ctrl + 3.3v 1k v swing (pk-pk) 240 240
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 6 millimeters inches dim min max min max a 1.75 0.069 a 1 0.10 0.25 0.004 0.010 a 2 1.25 1.45 0.049 0.057 a 3 0.25 0.01 b p 0.36 0.49 0.014 0.019 c 0.19 0.25 0.0075 0.0100 d 4.8 5.0 0.19 0.20 e 3.8 4.0 0.15 0.16 e 1.27 0.050 h e 5.80 6.20 0.228 0.244 l 1.05 0.041 l p 0.40 1.00 0.016 0.039 q 0.60 0.70 0.024 0.028 v 0.25 0.01 w 0.25 0.01 y 0.10 0.004 z 0.30 0.70 0.012 0.028 0 o 8 o 0 o 8 o package diagram soic 8 n otes: 1. dimensions d and e do not include mold protrusion. 2. maximum mold protrusion for d is 0.15mm. 3. maximum mold protrusion for e is 0.25mm.
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 7 package diagram mlp 8 n otes 1. dimensioning and tolerancing conform to asme t14-1994. 2. the terminal #1 and pad numbering convention shall conform to jesd 95-1 spp-012. 3. dimension b applies to metallized pad and is measured between 0.25 and 0.30mm from pad tip. 4. coplanarity applies to the exposed pad as well as the terminals. millimeters dim min max a 0.80 1.00 a1 0.00 0.05 a3 0.25 ref b 0.30 0.35 d 2.90 3.10 d2 1.65 1.95 e 2.90 3.10 e2 1.65 1.95 e 0.65 bsc l 0.35 0.45 aaa 0.25 bbb 0.10 ccc 0.10
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 8 package diagram tssop 8 millimeters dim min max a 1.10 a 1 0.05 0.15 a 2 0.80 0.95 a 3 0.25 b p 0.25 0.45 c 0.15 0.28 d 2.90 3.10 e 2.90 3.10 e 0.65 h e 4.70 5.10 l 0.94 l p 0.40 0.70 v 0.10 w 0.10 y 0.10 z 0.35 0.70 0 o 6 o n otes: 1. dimensions d and e do not include mold protrusion. 2. maximum mold protrusion for d is 0.15mm. 3. maximum mold protrusion for e is 0.25mm.
az10ep16vs az100ep16vs november 2001 * rev - 3 www.azmicrotek.com 9 arizona microtek, inc. reserves the right to change circuitry a nd specifications at any time without prior notice. arizona mic rotek, inc. makes no warranty, representation or guarant ee regarding the suitability of its products for any particular purpose, nor does a rizona microtek, inc. assume any liability arising out of the applica tion or use of any product or ci rcuit and specifically disclaims any and all liability, including without limitation special, consequential or inci dental damages. arizona microtek, inc. does not convey a ny license rights nor the rights of others. arizona microtek, inc. products are not designed, intended or authorized for use as component s in systems intended to support or sustain life, or for any other applicati on in which the failure of the arizona microtek, inc. product co uld create a situation where personal injury or death may occur. should bu yer purchase or use arizona microtek, inc. products for any such unintended or unauthorized application, buyer shall indemnify a nd hold arizona microtek, inc. a nd its officers, employees, subs idiaries, affiliates, and distributor s harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges tha t arizona microtek, inc. was negligent regarding the design or manufacture of the part.
|
